Celestron NexStar 5i Manuel d'instructions télécharger pdf (Page 9)

I 1716 I

the eyepiece using the direction keys on the hand control-

ler and press the ALIGN button. This will accept the star

as the ﬁrst alignment position. (There is no need to adjust

the slewing rate of the motors after each alignment step.

The NexStar automatically selects the best slewing rate for

aligning objects in both the ﬁnderscope and the eyepiece).

7. For the second alignment object, choose a bright star or

planet as far as possible from the ﬁrst alignment object.

Once again, use the direction keys to center the object in

the ﬁnderscope and press ENTER. Center the object in

the eyepiece, then press the ALIGN button.

8. Repeat the process for the third alignment star. When the

telescope has been aligned to the ﬁnal stars, the display

will read “Align Success.”

Aligning with Auto Two Star

After the ﬁrst star is selected and centered, the second star

will automatically be chosen for the best possible alignment.

Once selected, the telescope will automatically slew to the

second alignment star to complete the alignment.

1. Flip the NexStar’s power switch on. The hand control will

display “Verifying Packages…” After a few seconds it will

display “Evolution.” Scroll down using the “9” Scroll key

and press ENTER to choose Auto Two Star.

2. Press ENTER and you will be prompted to enter the local

time in 24-hour format. Ex. 21:00 for 9PM.

3. Select Daylight Savings or Standard Time, toggle the 6 &

9 (up and down scrolling keys) to change.

4. Select time zone, then enter the date. Press ENTER each

time to proceed to the next prompt.

5. The display will now prompt you to “Select Star 1” from

the displayed list on the hand control. Use Up and Down

scroll keys (6 and 9 on the keypad) to scroll to the desired

star and then press ENTER.

6. Use the direction keys to slew the telescope to the star

you selected. Center the star in the StarPointer and press

ENTER. Finally, center the star in the eyepiece and press

ALIGN.

7. The hand control will automatically display the most

suitable second alignment star that is above the horizon.

Press ENTER to automatically slew the telescope to the

displayed star. If for some reason you do not wish to select

this star (perhaps it is behind a tree or building), you can

either:

• Press the UNDO button to display the next most suitable

star for alignment.

• Use the UP and DOWN scroll keys to manually select any

star you wish from the entire list of available stars.

8. Repeat the same process of centering the star in your

StarPointer, press ENTER, then center in your eyepiece

and press ALIGN.

When the telescope has been aligned to both stars the

display will read Alignment Success. You are now ready to

ﬁnd your ﬁrst object.

Using a Wedge with EQ North /

EQ South Alignment

EQ North and EQ South Alignments assist the user in

aligning the telescope when polar aligned on an optional

equatorial wedge.

EQ AutoAlign

1. Select EQ North (for northern hemisphere) or South (for

southern hemisphere) Align from the alignment options

and press ENTER.

2. Enter time, date, and location information as with all other

alignments.

3. Select EQ AutoAlign method and press ENTER

4. Use the direction arrow keys to move the telescope until

the altitude and meridian index markers are aligned. The

altitude index marker is located at the top of the fork arm,

and the meridian marker is on the base of the fork arm.

The tube should be perpendicular to the fork arm and

facing the meridian.

5. The display will now prompt you to “Select Star 1” from

the displayed list on the hand control. Use Up and Down

scroll keys (6 and 9 on the keypad) to scroll to the de-

sired star and then press ENTER.

6. Use the direction keys to slew the telescope to the star

you selected. Center the star in the StarPointer and press

ENTER. Finally, center the star in the eyepiece and press

ALIGN.

7. The hand control will automatically display the most

suitable second alignment star that is above the horizon.

Press ENTER to automatically slew the telescope to the

displayed star. If for some reason you do not wish to select

this star (perhaps it is behind a tree or building), you can

either:

• Press the UNDO button to display the next most suitable

star for alignment.

• Use the UP and DOWN scroll keys to manually select any

star you wish from the entire list of available stars.

8. Repeat the same process of centering the star in your

StarPointer, press ENTER, then center in your eyepiece

and press ALIGN.

When the telescope has been aligned to both stars the

display will read Alignment Success. You are now ready to

ﬁnd your ﬁrst object. Tracking will now occur equatorially,

moving in just one direction to keep the object centered in

the telescope’s ﬁeld of view without rotating. This tracking is

suitable for astroimaging.

NexStar Evolution Telescope

Settings in NexStar+ Hand Control

Press Menu, scroll to the “Peripherals” menu and press

ENTER. Here, you can control L.E.D. brightness of the logo

lights and accessory tray lighting, check the battery status, or

set more advanced features including external power supply

and USB charge port settings.

Adjust the L.E.D. Brightness

1. Scroll to “Mount Lights” and press ENTER.

2. Scroll to select Tray Light, WiFi Light, or Logo Light and

press ENTER.

3. Select a brightness value from 0-10, 0 being OFF, and

10 being fully lit. Press ENTER and the new brightness

setting will take effect.

Power

1. Scroll to “Power” and press ENTER.

2. Scroll to select “Status” or “External Power” and press

ENTER

• Status will display the battery voltage, if the battery

charge state is High, Medium, or Low, and if the battery

is charging or discharging.

• External Power allows you to select a higher input current

if you are using a higher capacity power supply. Values

can be between 2 and 5 amperes as speciﬁed on your

power supply. Do not change this setting unless you

are using a larger capacity supply. The included power

supply should always be set to 2.0A.

WiFi

1. Scroll to “WiFi” and press ENTER.

2. Scroll to select “Status” or “Enable/Disable” and press

ENTER

• Status will display the WiFi mode, Direct Connect or

Access Point, and whether or not the WiFi is connected

to a network

• Enable/Disable will optionally allow you to disable the

WiFi broadcast. The WiFi L.E.D. will shut off indicating it

has been disabled. Every time you power off and on the

mount again, this setting defaults to Enabled.

USB Charge Port

1. Scroll to “Charge Port” and press ENTER.

2. Press ENTER to toggle between “Automatic” or “Always

On”. “Always On” keeps the charge port going, even in a

low battery condition. “Automatic” automatically disables

the USB Charge Port when battery power is low.

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15

Commentaires sur ces manuels

Pas de commentaire

Celestron NexStar 5i Manuel d'instructions Page 9

Commentaires sur ces manuels

Produits connexes et manuels pour Télescopes Celestron NexStar 5i